\\ Post Your Car vol. Been a minute //

How do you guys think these would look on a white A8L?  Rohana RC20

01.11-500x500.jpg


Edit* or option B.  Rohana RC10 

01-500x500.jpg
 
Last edited by a moderator:
How do you guys think these would look on a white A8L?  Rohana RC20

01.11-500x500.jpg


Edit* or option B.  Rohana RC10 

01-500x500.jpg


How do you guys think these would look on a white A8L?  Rohana RC20

clean


I was going to go for the RC20s, bu then I started looking at side profile shots of them and I could not get past how they looked and rivets on them. It just wasn't for me. I decided to go with the RC10s and I couldn't be happier :smokin

I never posted my new setup, but my car broken into my car and someone got my for my CV3s back in October. Left me uneven on a spare tire jack and the front lip on the ground on the other side with a busted out window :smh:
Luckily the tires were worn and camber wear on them and I was going to need new ones by the end of summer anyways...and I got to go staggered on this setup :smokin

Here are some RC20 side shots I looked at:
700

900


Here are a couple RC10 shots that won me over:
700

700

700




For some reason, they are only on this finish of the RC-20. The all black ones do not have them and they nice looking. Either way, it will come out looking good and they are hot wheels. It could also change how they look when they are 22s since I was looking at 20s. I am just guessing you are going 22s since you are talking about putting them on an A8L.
 
Last edited:
@WrightOne86   for whatever reason I didn't notice the rivets until now and I am not feeling them.  Think I'm gonna go with the much cleaner RC10 with the machined black as opposed to matte black.  Actually, with it being a white car with red calipers maybe matte would look better? 
ohwell.gif
  I'm so indecisive. 

And i'm going with 20's
 
Last edited by a moderator:
@WrightOne86
  for whatever reason I didn't notice the rivets until now and I am not feeling them.  Think I'm gonna go with the much cleaner RC10 with the machined black as opposed to matte black.  Actually, with it being a white car with red calipers maybe matte would look better? :\   I'm so indecisive. 

And i'm going with 20's
With the white car, I would personally go with the all black look. It is really up to you on how you want your car to look though. The all black would be a little more aggressive than the silver and machined black look. If you go with the all black, you could still grab the RC-20s since they do not have the rivets though. I grabbed some pics of off their FB page for you to check out.

RC20s
1000


RC10s
1000
 
thanks for the pics - lot's of good stuff on their FB page.  This may have sold me since I have the red calipers.

1519265_566701423417722_1822698027_o.jpg
 

vs

964841_530609883693543_229656914_o.jpg
 
Last edited by a moderator:
Of course I had to see this on their IG - this is the machined black.  Throws another wrench in the wheel 
laugh.gif
 pun intended
 
400
+
400






Or
400



Which rims

Car is not mine (yet)
Please don't do the wire wheels just because of menace to society, leave that ish in the past Where it belongs, wires go on big bodied American rwd cars or trucks only IMO!

Personally, I prefer the black wheels that are already on there, but the bbs are cool.
 
Don't really know much about staggering, was just going to order as is.  But the tires they suggest are Hankook K110 V12.
 
if it's rwd...stagger. get the biggest wheel and tire you can back there. makes the car look so much better.
 
if it's rwd...stagger. get the biggest wheel and tire you can back there. makes the car look so much better.
This. Wheels with concavity look better the wider you go, so @reazsal go as wide as you can. You can still do a staggered setup, even if it's awd, as long as the tire heights are the same on all 4 tires.
 
Back
Top Bottom